Austral FoldAway Rotary Clothesline Installation Guide 

The Austral FoldAway Rotary Clotheslines are made to last, crafted with durability in mind to ensure you get years of reliable use. To make the most of your new clothesline, it’s really important to follow the installation instructions carefully.

Getting the setup right is key—not only to avoid any potential damage to your clothesline but also to make sure you don’t accidentally void the warranty. A little preparation now can go a long way in keeping your folding rotary clothesline working perfectly for years to come! TABLE OF CONTENTS

Parts Supplied:

• 1 x Clothesline Handle Grip – Black

• 1 x Clothesline Handle Shaft – Black

• 1 x Clothesline Handle Back Cover – Black

• Clothesline Accessory Pack Includes:

  • 1 x 8mm x 150mm Galvanised Pin

  • 1 x Ground Socket Cap

Folding Rotary Clothesline Installation Guide

Read the Clothesline Installation Instructions

Before you begin with the clothesline installation, take the time to carefully read through the installation instructions, provided, for your new Austral Foldaway Rotary.

Understanding each step will help ensure the clothesline installation process goes smoothly and without any surprises.

While reviewing the installation instructions, also check the contents of your Foldaway Rotary box.

Tick off each item to confirm that everything is included, and make sure you have all the necessary tools on hand. This will save you time and effort, helping you avoid delays during the clothesline installation process.

Site Preparation

Select a Suitable Site:

Choose a location for your clothesline that allows minimum 500mm clearance, from the end of each arm. This will give ample room for your washing to move freely.

Dig a Hole:

Hole Size: 600mm deep and 200mm in diameter.

Backfill: Fill the bottom of the hole with drainage gravel or stones. The Ground Socket’s top lip should sit just above the ground level (as shown in Figure 1).

Height Setting

Important: If installing your new folding rotary clothesline on sloping ground, be mindful of the height setting to ensure the clothes line arms pitch upwards correctly. Also, consider the persons height and if they will stand in one place or have to move around the clothes line when hanging the washing.

Install the Head Section:

Slide the pre-corded clothesline Head Section into the top of the Column.

The black plastic Cross (that bolts to the 4 arms) will slide down over the column.

Stand the clothesline column upright and rotate the head section until the locking mechanism aligns.

The clothesline head will drop once, then rotate again to drop a second time.

Set Height:

The clothesline ground socket has multiple height settings, indicated by partially hollowed holes on the side. Slide the Column into the Ground Socket and stand it upright. Ensure the lip of the socket is just above the ground level.

Adjust Height (if needed):

If necessary, raise the clothesline Head Section by carefully opening the arms. Check that the lines aren’t twisted or caught (especially at the arm tips).

Ensure the arms are free to move upward until the Cross meets the black plastic bush. Flip the latch to secure them together.

Select the Height:

Once the clothes line arms are raised and the rotary clothesline is wound down fully, check the head height clearance of the main person using the rotary.

Adjust by selecting a suitable height hole on the Ground Socket. The clothes line can be wound up by 270mm from its lowest position, which will make the outer lines higher from the ground.

Set the Pin:

Once the correct height is set, fold down the washing lines Head Section and secure the arms with the Line Retainer.

Remove the Column from the Socket.

Place the Galvanised Pin into the selected height hole on the ground socket and use a hammer to punch the pin through.

Repeat for the other side. The pin locks the clothesline column in place and sets the height.

Fitting the Clothesline Handle

Attach the Handle Shaft:

Insert the clothesline handle shaft into the handle grip. Push the split end of the shaft through the hole at the bottom of the handle. The split will expand and lock into place.

Attach the Handle Back Cover:

Clip the clothesline handle cover onto the back of the handle by pushing the pins into the locating holes. Press firmly to secure.

Concrete the Ground Socket

Mix Concrete:

Quick-setting cement is recommended, but you can mix your own using a ratio of 3 parts gravel, 1 part sand, and 1 part cement. Add enough water to make the mix damp enough to hold together when squeezed by hand.

Install the Clothes Line Ground Socket:

Stand the ground socket in the centre of the hole, ensuring it aligns with the correct height setting. Open the washing lines head section and check for the correct height and the level of the socket to the ground surface. Adjust as necessary.

Fill the Hole:

Fold the arms down and fit the Line Retainer for final installation. Ensure the handle faces the correct direction (towards the path).

Begin by adding 50mm of gravel into the hole. Then, pour the concrete mix to fill the hole up to about halfway.

Check the level of the Main Column and tamp the concrete down to remove air pockets. Recheck the level and fill the hole within 20mm of the top.

Tamp again to settle the concrete, and finish by filling the last 20mm with a mix of 2 parts sand and 1 part cement.

Curing Time:

Leave the hoist undisturbed for 48 hours to allow the concrete to fully set.

Important Information & Operating Instructions

Regular Maintenance:

To prevent debris from causing the hoist to seize up, remove the hoist from the Ground Socket several times a year for cleaning.

Folding the Rotary Hoist:

To fold, wind the Head Section down, place your fingers on top of the Bush, and squeeze the Cross and Arms upward.

Lift the latch and gently lower the cross section to fold the arms down. Use the Line Retainer to secure the lines and prevent tangling during removal.

Removing the Clothesline:

Once the clotheslines head section is folded down and secured, hold the Main Column with both hands. Lift and rotate the clothesline column clockwise to remove it from the socket.

Place the Socket Cap onto the Ground Socket to protect it.

Reinstalling the Clothesline:

Insert the rotary hoist clothesline into the ground socket and gently lower it onto the Pin. Rotate the Main Column until it locks into position. Rotate anti-clockwise to lock the column securely.

Unfolding the Clotheslines Head Section:

Remove the Line Retainer, grasp the arms, and gently pull them outward. Raise the Cross as far as it will go, then lower the latch into the locked position.

Warning: If the Cross doesn’t lift easily, the clotheslines cords might be tangled. Carefully check the lines and never force the Cross into position.

Tightening the Lines:

To tighten the lines, open the lever on the Line Tension Lock. Start from the inner lines and work your way outwards, pulling each cord tight as you go.

Lock the lever back into place once all lines are tightened.

During Use: Distribute washing evenly to allow the hoist to rotate smoothly.

If it’s windy, wind the Head Section down into the locked position. To rotate, simply pull on one arm while in this position.

After use, wind the hoist back up to allow the Head Section to rotate freely in the breeze.

By following these instructions carefully, your Austral FoldAway Rotary Hoist will provide reliable and durable service for years. Enjoy your new clothesline!

Professional Clothesline Installation Service 

If you’re not keen on installing your new clothesline at The Clothesline Store we make clothesline installation incredibly easy, with our professional clothesline installation service that ensures your clothesline is set up effortlessly.

Whether you’re choosing a fold down mounted, retractable, or the Austral FoldAway Rotary clothesline, our expert installers are ready to help across the East Coast of Australia, including Sydney, Melbourne, Brisbane, Adelaide, and beyond—covering areas like Geelong, the Gold Coast, and Newcastle.

To book your clothesline installation service, simply select "Yes, Install My Clothesline" (or "Yes, Install and Remove Old Clothesline") when placing your order.

Pick your clothesline, choose the clothesline installation option, and you’re on your way to having your new clothesline installed!  

Top Tip:

Not all clothesline retailers offer clothesline installation services, if clothesline installation or clothesline removal is important to you, make sure these services are available before purchasing!

The Clothesline Store is the only retailer in Australia with its own dedicated clothesline warehouse, offering the largest inventory of stocked products. This allows for same-day or next-business-day shipping, ensuring faster delivery of all stocked clotheslines and accessories.